random user submitted photo
Search found 5053 matches
Re: Waiex training
Michael, The 140 is a good airplane. I flew one back in NY and was restoring it. It was a chapter project. When I had to move I was separated from the project. It would have been a good choice to buy a 140 instead of the Waiex kit on the one hand - for about half the money I could have a flying airp...
- Thu Sep 26, 2013 5:02 pm
- Forum: General Discussion
- Topic: Waiex training
- Replies: 2
- Views: 2922
Waiex training
My Waiex substitute is a rental C140.
Photo deleted for quota
Photo deleted for quota
- Tue Sep 24, 2013 5:38 pm
- Forum: General Discussion
- Topic: Waiex training
- Replies: 2
- Views: 2922
Re: Cotton Waiex 191 - N191YX
My forward spars for my stabilizers are riveted.
- Sun Sep 22, 2013 6:44 pm
- Forum: Photo Album
- Topic: Cotton Waiex 191 - N191YX
- Replies: 1536
- Views: 4095391
Distractions
We would have riveted more last night, but Adam wanted to cruise the airport a little in our vintage golf cart (73 Harley model D gas). We came upon a couple avengers in the neighborhood, wings folded and engines running. Waited to see them depart. The local RV squadron did a formation departure too.
- Sun Sep 22, 2013 6:47 am
- Forum: General Discussion
- Topic: Distractions
- Replies: 0
- Views: 1396
Re: Cotton Waiex 191 - N191YX
First rivets!
- Sat Sep 21, 2013 5:32 pm
- Forum: Photo Album
- Topic: Cotton Waiex 191 - N191YX
- Replies: 1536
- Views: 4095391
Re: Cotton Waiex 191 - N191YX
Skins....
- Fri Sep 20, 2013 9:45 am
- Forum: Photo Album
- Topic: Cotton Waiex 191 - N191YX
- Replies: 1536
- Views: 4095391
Re: Heat and aluminum
One chart I looked up says that either the tensile ultimate or yield strength does not change at 350F for less than 6 minutes on temperature, or for 300F at less than 30 minutes. Ageing temperature for bringing the material to the T6 condition is 320F. I have belt sanded a lot of edges, and I don't ...
- Thu Sep 19, 2013 1:13 pm
- Forum: General Discussion
- Topic: Heat and aluminum
- Replies: 3
- Views: 2498
Re: Heat and aluminum
Tony,
Either annealing or changing temper of aluminum generally requires temps in excess of 500F. I have friends at work who can more definitively answer the question for 6061-T6. I will get back to you. I think you are fine however.
Either annealing or changing temper of aluminum generally requires temps in excess of 500F. I have friends at work who can more definitively answer the question for 6061-T6. I will get back to you. I think you are fine however.
- Thu Sep 19, 2013 6:54 am
- Forum: General Discussion
- Topic: Heat and aluminum
- Replies: 3
- Views: 2498
Re: Cotton Waiex 191 - N191YX
I assembled the left hand side with similar results. This time I was careful to take the springback out of the flanges, so the bottoms were 90 and the tops matched the angle of the front spar in the plans. I did not think that would make a difference for a dry fit, as on the right side the clecoes w...
- Wed Sep 18, 2013 10:09 pm
- Forum: Photo Album
- Topic: Cotton Waiex 191 - N191YX
- Replies: 1536
- Views: 4095391
Re: Cotton Waiex 191 - N191YX
Trial assembly of right stab. Root rib seems too short though it measures up right.
- Tue Sep 17, 2013 10:54 pm
- Forum: Photo Album
- Topic: Cotton Waiex 191 - N191YX
- Replies: 1536
- Views: 4095391
