Kit Piece Inventory

Use this area for aviation related general discussions, newsworthy items, and non model specific topics.

Kit Piece Inventory

Postby dbdevkc » Wed Jul 13, 2011 2:56 pm

I just received delivery of my Waiex airframe kit. My question is how to go about doing the piece inventory? Is there a master list anywhere, or am I to be going through the plans page by page...

Thanks,
Kevin - W0169
[color=#800000]Kevin Conklin
Building Waiex #169
dbdevkc
 
Posts: 193
Joined: Sun Jun 26, 2011 9:18 am
Location: Washingtonville, NY

Re: Kit Piece Inventory

Postby Andy Walker » Wed Jul 13, 2011 4:13 pm

You should have gotten an inventory list checked off by the Sonex folks, maybe in with your packing list? I just started opening boxes, looked at each piece and found it on the list and checked it, then when I ran out of parts went down and make sure everything was accounted for.
User avatar
Andy Walker
 
Posts: 375
Joined: Sat Jul 02, 2011 10:27 pm

Re: Kit Piece Inventory

Postby dbdevkc » Wed Jul 13, 2011 4:38 pm

I didn't find a packing list. Found a 'welcome' cover letter with a copy of the liability release that I had signed and an envelope with a patch and pin, but no inventory list... :?
[color=#800000]Kevin Conklin
Building Waiex #169
dbdevkc
 
Posts: 193
Joined: Sun Jun 26, 2011 9:18 am
Location: Washingtonville, NY

Re: Kit Piece Inventory

Postby MichaelFarley56 » Wed Jul 13, 2011 5:24 pm

I know this sounds dumb but have you looked through all the boxes? Andy is right on...there should be an inventory list of several pages that you can use. Look through everything (including the plans) and if you can't find anything give Sonex a call.
Mike Farley
Waiex #0056 - N569KM
Jabiru 3300A #1706
MGL Panel
MichaelFarley56
 
Posts: 1484
Joined: Thu Jun 02, 2011 11:38 pm
Location: Columbus, Ohio

Re: Kit Piece Inventory

Postby Sonex1517 » Wed Jul 13, 2011 6:18 pm

Kevin

Be certain you look all over every box and piece of pallet - somewhere there is a list of all included when they shipped. Ours was a bit hard to find and had slightly faded printing but was usable. And save it! You will find need for it.

Congrats! We just put the skin on the vertical stabilizer. Lots of work to get to this point but worth it all....and best thing to me is that the parts I ruined Sunday only cost $45 to replace! :-)

Let me know if you need anything from our end - we are not far ahead of you....
Robbie Culver
Sonex 1517
Aero Estates (T25)
First flight 10/10/2015
375+ hours
Jabiru 3300 Gen 4
Prince P Tip
Taildragger
N1517S
User avatar
Sonex1517
 
Posts: 1670
Joined: Fri Jun 03, 2011 10:11 am
Location: T25 Aero Estates, Frankston, TX

Re: Kit Piece Inventory

Postby dbdevkc » Wed Jul 13, 2011 10:29 pm

Off to a rocky start here. Just finished going through everything. No packing list or inventory. Seems like that should have been with the cover letter and flight manual. Not sure about anything else, but should the motor mount be included - is that something that I could possibly overlook ...?
[color=#800000]Kevin Conklin
Building Waiex #169
dbdevkc
 
Posts: 193
Joined: Sun Jun 26, 2011 9:18 am
Location: Washingtonville, NY

Re: Kit Piece Inventory

Postby N111YX » Thu Jul 14, 2011 8:21 am

Kevin, if you are missing the motor mount perhaps you do not have all of the boxes...???
Kip

2010 Waiex 0082 (first flight May 2010)
Jabiru 3300 #1637 and #3035
Dynon D-180
Becker radios
Garmin GDL 82 ADS-B
1175 hours
48 states visited
Based near Atlanta

Also flying a...
2000 Kolb Firestar II, Rotax 503, 575 hours
N111YX
 
Posts: 711
Joined: Fri Jun 03, 2011 9:43 am
Location: Atlanta, GA USA

Re: Kit Piece Inventory

Postby Sonex1517 » Thu Jul 14, 2011 12:27 pm

I'd give them a call Kevin - so far all of my interactions with Sonex have been very good. They accidentally charged me to crate the tail kit and when I asked they refunded the cost in minutes....

Robbie
Robbie Culver
Sonex 1517
Aero Estates (T25)
First flight 10/10/2015
375+ hours
Jabiru 3300 Gen 4
Prince P Tip
Taildragger
N1517S
User avatar
Sonex1517
 
Posts: 1670
Joined: Fri Jun 03, 2011 10:11 am
Location: T25 Aero Estates, Frankston, TX

Re: Kit Piece Inventory

Postby dbdevkc » Fri Jul 15, 2011 1:21 am

Mystery solved. Spoke with Mark and the packing list/inventory is typically in a plastic envelope on the outside of the box that contains the motor mount ... oh and by the way, the motor mount is on back order. I am guessing that because the mount is B/O'd, the list didn't get attached by accident. They do scan them, so they were able to send me a PDF.
[color=#800000]Kevin Conklin
Building Waiex #169
dbdevkc
 
Posts: 193
Joined: Sun Jun 26, 2011 9:18 am
Location: Washingtonville, NY

Re: Kit Piece Inventory

Postby Andy Walker » Fri Jul 15, 2011 9:34 am

Great, glad you got your parts sheet!

Th inventory process is a PITA and one of the less fun times in the process, but at least you get a to see what a lot of the parts look like (and you'll see a few where you say "what the heck is THAT for?!?").
User avatar
Andy Walker
 
Posts: 375
Joined: Sat Jul 02, 2011 10:27 pm

Next

Return to General Discussion

Who is online

Users browsing this forum: No registered users and 8 guests

cron